Pin Field Depth Alignment Parameters for Water Retted Flax Processing
Pin field depth for water retted flax requires a 1.8 mm to 2.2 mm tip-to-base clearance to control split bundles without transverse fibre pinching or breakage.

Penetration
Water-retted flax line sliver presents a distinct mechanical challenge inside the drafting zone of an intersecting gill box. Anaerobic fermentation in warm water tanks dissolves calcium pectate cross-links more thoroughly than dew retting. This biochemical reaction yields supple, fine elementary fibre bundles with lower inter-fibre cohesion and higher transverse compliance.
Operating gill drawing frames on water-retted material demands exact regulation of the vertical distance between the opposing pin sets. The upper and lower pin tips enter the moving sliver mass from opposite sides. Setting the pin penetration overlap between positive 1.8 mm and 2.2 mm establishes continuous frictional contact across the strand thickness without crushing the bast bundles against the steel faller bars.
Pin tip clearance from the opposing faller bar stock determines whether drafting proceeds by controlled slippage or by destructive fibre shearing. When the pin tips plunge too deep, closing the gap to less than 1.0 mm from the opposing faller bed, the rigid steel tips pin the flexible water-retted filaments against the metal base. The fast front drafting rollers then pull the clamped fibres against this artificial pinch point, severing the long line strands into short fragments.
Setting the gap wider than 2.8 mm permits the central core of the sliver to float freely between the upper and lower pin beds. Floating fibres accelerate prematurely toward the front nip, causing thick-and-thin drafting waves and uneven sliver weight.
Water-retted line sliver drawn with a 2.0 mm pin overlap generates an evenness coefficient of variation below 3.2 percent on a forty-gram-per-metre delivery.
Fibre technicians determine the entry alignment by measuring the vertical distance between the upper and lower faller bar bodies at the crossover point using machined step gauges. Water-retted bundles average 18 to 22 micrometres in elementary diameter, bundled into technical filaments of 45 to 65 micrometres. These dimensions are forty percent smaller than coarse dew-retted bundles.
The reduced bundle girth allows the sliver to compress into a dense sheet under minimal downward force. Adjusting the vertical eccentric cams on the gill head shifts the upper faller track relative to the lower track, locking the pin penetration depth across the entire working width.
Processing speeds influence dynamic penetration. High faller drop frequencies generate air currents that lift light flax fibres out of the pin matrix before the needles fully engage. Setting the draft ratio between 6.5 and 8.0 on the first drawing passage balances the input sliver bulk against the holding power of the pins.
Excessive draft pulls the fibres through the pin field faster than the inter-fibre friction can damp the motion. Controlled penetration maintains continuous contact between the steel pin flanks and the pectin-depleted fibre surfaces, arresting premature acceleration toward the delivery rollers.

Faller
Mechanical movement of the faller bars defines the boundary of the drafting zone. In an intersecting screw-driven or chain-track gill box, top and bottom bars move forward synchronously at speeds slightly exceeding the surface speed of the back feed rollers. The pins project vertically from the bar body at forward angles between zero and four degrees.
This forward rake counteracts the pulling force exerted by the front drafting rollers. Water-retted flax demands round pins with polished, conical tips to part the slippery, degummed bundles without snagging or splitting the technical fibres down their longitudinal axes.

Where Does Over-Penetration Break Water-Retted Bundles?
Fibre shearing occurs directly beneath the pin tips at the point of maximum mechanical overlap. Because water retting removes the gummy cellular encrustations, individual elementary fibres slide past each other readily under tension. If vertical pin alignment causes the tips to strike the opposing metal faller bed, the transverse pinching force exceeds the lateral shear strength of the wet-softened cellulose walls.
Bundle fracture happens instantaneously. The broken tips accumulate as short bast tow, dropping into the waste tray beneath the gill head.
| Drawing Passage | Sliver Weight Input (g/m) | Pin Density (pins/cm) | Pin Overlap (mm) | Front Roller Nip Distance (mm) | Draft Ratio Range |
|---|---|---|---|---|---|
| First Passage Line | 38.0 to 45.0 | 2.5 to 3.0 | 2.2 to 2.4 | 68.0 to 72.0 | 5.5 to 6.8 |
| Second Passage Line | 18.0 to 22.0 | 4.0 to 5.0 | 1.8 to 2.0 | 62.0 to 66.0 | 6.5 to 7.8 |
| Third Passage Line | 7.5 to 9.5 | 6.5 to 8.0 | 1.4 to 1.6 | 56.0 to 60.0 | 7.5 to 9.0 |
| Finishing Intersecting | 3.0 to 4.2 | 10.0 to 12.0 | 1.0 to 1.2 | 50.0 to 54.0 | 8.0 to 10.5 |
Faller timing errors compound depth alignment defects. When the upper faller drops into the sliver stream a millisecond out of phase with the lower bar, the downward momentum strikes the fibres against a static lower pin tip rather than entering an open gap. This impact shatters the brittle ends of high-grade Courtrai or Lys water-retted line flax.
Technicians verify phase synchronisation by turning the gill head manually while tracking the drop cams with dial indicators. The bars must clear each other with a lateral margin of 0.35 millimetres.
- Mechanical bed leveling eliminates side-to-side variation by adjusting the four corner screw jacks until the upper and lower faller guides sit parallel within 0.05 mm across a 250 mm working field.
- Cam profile inspection detects localized flat spots on the lower drop cams where uneven wear causes sudden pin depth drops during bar deceleration. Bars jump under load.
- Pin deflection testing checks whether loaded pins bend backward under sliver resistance, measuring tip displacement against a stationary dial gauge under a lateral load of five Newtons.
- Nip-to-field alignment positions the leading edge of the forward-most faller bar exactly 28 mm from the center line of the bottom fluted front drafting roller. Short spaces drop line yield.
A supplier will often attribute irregular sliver linear density to biological retting variance rather than investigate mechanical faller guide wear.

Cohesion
Residual intercellular gums dictate the pulling force required to draft water-retted flax. During warm-water tank retting, bacterial action consumes the rhamnogalacturonan and polygalacturonic acid fractions of the middle lamella. The residual pectin content drops to 1.8 to 2.4 percent by weight, compared to 3.5 to 4.8 percent in dew-retted stalk bast.
Lower pectin reduces bundle rigidity. The sliver behaves like a compliant ribbon rather than a stiff, resilient mat. Pin penetration must be set tighter than in dew-retted processing to compensate for the absence of natural bundle stiffness.
Pectin depletion below two percent reduces inter-fibre friction and allows draft propagation at pin penetrations that would choke dew-retted slivers.
Drafting force meters mounted on the front roller bearing blocks record the pull resistance of the advancing sliver. In water-retted flax, drafting resistance peaks between 12 and 18 Newtons per kilotex of input material when the pin overlap sits at 2.0 mm. Dew-retted material under identical pin settings registers drafting forces between 26 and 35 Newtons per kilotex.
The lower resistance in water-retted stock permits higher pin density along the faller bar. Gills process water-retted flax with eight to ten pins per centimetre where dew-retted stock requires five to six pins to avoid stalling the faller screws.
| Fibre Preparation Parameter | Tank Water Retted | Dew Retted Normandy | Chemical Degummed | |
|---|---|---|---|---|
| Residual Pectin Fraction (%) | 1.8 to 2.3 | 3.6 to 4.5 | 0.8 to 1.2 | |
| Static Friction Coefficient (fibre-to-steel) | 0.22 | 0.31 | 0.18 | |
| Mean Bundle Tenacity (cN/tex) | 48.0 to 56.0 | 42.0 to 48.0 | 32.0 to 38.0 | |
| Pin Penetration Setting (mm overlap) | 1.8 to 2.2 | 1.2 to 1.5 | 2.4 to 2.8 | |
| Faller Velocity Limit (drops/min) | 1400 | 1100 | 1600 | |
| Values established under standard testing atmosphere of 20 degrees Celsius and 65 percent relative humidity according to ISO 139 conditioning protocols. | ||||
High moisture levels in the preparation room alter fibre cohesion drastically. Cellulose absorbs moisture rapidly once the protective wax-pectin sheath degrades. Operating the drawing room above 70 percent relative humidity causes water-retted flax to adhere to the steel pins, creating lap-ups on the fallers.
Maintaining relative humidity at 62 to 65 percent preserves the natural suppleness of the flax without triggering static electric charges or moisture-induced surface cling. Pins release cleanly.
Internal friction inside the bundle bundle array dictates the attenuation rate. When the drafting rollers grip the leading tips of the fibres, tension transfers backward into the pin field across a distance of several centimetres. If the pin field depth is insufficient, this tension wave travels all the way to the back rollers.
Drafting then occurs uncontrollably across the entire bed. Correct pin penetration concentrates the drafting zone within the final 35 millimetres ahead of the front drafting nip.
The operational balance rests on matching the pin field depth to the precise degree of retting of each commercial lot.

Defect
Improper vertical alignment of the pin field produces distinctive structural yarn faults. Pin truncation severs the longest line fibres, shifting the staple length distribution downward. In water-retted flax, where high intrinsic fibre strength enables fine yarn counts from metric count 60 to metric count 100, losing the long-staple fraction degrades the commercial value of the spun yarn.
The classer detects this defect by extracting fibres from the drafted sliver and laying them out on a velvet sorting board. A truncated sliver displays a squared-off tail of broken 40-millimetre fragments rather than a smooth, tapered staple diagram.

What Pin Clearances Prevent Sliver Choking?
Faller pins must maintain a lateral clearance of 0.8 to 1.1 mm between adjacent needle rows on opposing bars to prevent mechanical choking. When the sliver mass exceeds the volumetric capacity of the pin interstices, fibres compact into dense, solid wedges between the needle bases. Water-retted fibres pack tightly because their surface profile lacks the rough, woody epidermis residues typical of dew-retted material.
Once compaction occurs, the sliver ceases to slip through the pins. The entire mass moves forward as a solid clump, jamming the faller bars or stripping the drive gears.
- Nep formation accelerates when blunt or barbed pins roll the loose elementary fibres into tight knots inside the intersecting field. Knots survive wet spinning.
- Sliver splitting occurs when pin rows penetrate without lateral stagger, slicing the output web into ribbons that separate upon entering the delivery trumpet.
- Roller wrapping follows under-penetration as uncontrolled floating fibres escape the pin field and adhere to the top synthetic-rubber drafting apron.
- Pin grooving develops on soft steel fallers when abrasive silica on unwashed flax wears deep tracks at the standard penetration line, altering clearance profiles over time.
Fibre damage increases exponentially when the clearance between upper and lower pin tips falls below the median diameter of the incoming sliver strand.
Nep counts on the finished roving reflect drawing pin alignment precision. When pin penetration matches the lot density, nep counts stay below 12 neps per gram of water-retted roving. Increasing the pin penetration depth by merely 0.6 mm into the interference zone elevates nep counts to 45 neps per gram.
These mechanical neps consist of sheared elementary fibres tangled around residual shive particles. They do not draft out during wet spinning. In the spinning trough, hot water at 70 degrees Celsius swells the neps into pronounced slubs, causing yarn breaks at the ring frame guide eyes.
Failure to correct pin alignment parameters voids spinning performance guarantees specified in commercial line contracts.

Outturn
Yarn manufacturing costs respond directly to the efficiency of the pin field setup. Hackled line flax prepared from water-retted straw carries a procurement cost of 6.20 to 8.50 euros per kilogram, more than double the price of dew-retted tow. Every percentage point of long line fibre converted into drawing room waste through pin shearing represents a direct write-off of expensive raw material.
Correct pin field alignment preserves 96.5 to 98.0 percent of the incoming sliver weight as drawn line sliver, transferring the full length of the bast bundles into the roving package.
Consider an industrial drawing line processing a 40-tonne commercial lot of water-retted Courtrai line flax destined for metric count 68 wet-spun yarn. Standard operating assumptions assign a raw material price of 7.40 euros per kilogram landed at the spinning mill. If technicians operate the three intersecting drawing passages with pin tip clearances set 0.8 mm too tight, transverse shearing crushes long filaments into drawing waste.
Waste generation jumps from an acceptable 2.5 percent to 6.8 percent across the three passages. The resulting loss of 1,720 kilograms of long line material shifts valuable fibre into drawing tow, which resells to upholstery spinners for only 1.80 euros per kilogram.
The financial impact carries directly into the cost per finished metre of woven linen. High drafting variation generated by inadequate pin penetration forces spinners to apply higher roving twist to prevent thin-spot breaks at the wet spinning frame. Extra roving twist restricts bundle drafting in the hot water trough, coarsening the yarn count and inflating fabric weight.
For a plain weave shirting cloth specified at 135 grams per square metre with a finished width of 150 centimetres, uneven drafting adds 8 to 12 grams per linear metre in surplus fibre mass to satisfy minimum tensile specifications. The mill expends unnecessary raw material to compensate for sliver irregularity.
Standard supply terms under the European Flax trade framework penalize count variation exceeding a four percent coefficient of variation by triggering mandatory price adjustments on delivered cones.
Spinning trials verify that aligning the pin penetration depth to within 0.1 mm of the target specification stabilizes the roving linear density. The yarn count coefficient of variation settles at 2.8 percent on metric count 80 wet-spun line yarns. Production shifts from defensive, overweight yarn sizing to precision count targeting.
Spindles run at 7,500 revolutions per minute with fewer than 18 ends down per one thousand spindle hours, maximizing the output of first-grade fabric from every delivered bale.
The physical limit of high-speed pin field control remains tied to the dynamic bending resistance of ultra-fine steel needles under varying sliver moisture levels.


